marchchill67

How to Replace a Kia Sportage Replacement Key For a number of Kia models the key comes with a keyless entry system built-in. The key can be compared to an electronic remote and can be changed with a fresh one from a Kia dealer or locksmith. Key fobs can stop working due to a number of reasons, such as an inactive battery, worn out buttons signal interference or water damage. Here are some tips to help you get your Kia sportage replacement key to work for good. How do you replace the remote key or smart key No matter if your Kia comes with an intelligent key, remote key push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually need replacement. This is especially relevant if your vehicle displays a message telling you that the remote or smart keys are not powered by batteries. This is a relatively easy process. To replace the battery in the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, pull the cover open. Inside the key fob will be a small screw that holds the battery in its place. Remove the old battery by detaching the screw with a small screwdriver. Then, you can insert the new battery and close the slit inside the key fob. Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock as expected, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you have to complete errands in Brandon. Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key needs to be programmed again, you must be aware of the key code written on the tag that identifies the key and record it in a safe location. How to replace a battery If the Kia key fob is unable to respond to pressing the lock/unlock button, it's a sign that the battery is not fully charged. A low battery may cause other issues, like the check engine light coming on or the engine not turning properly. Fortunately, replacing the key fob battery is a simple DIY project that requires just a few tools. Make sure you turn off your vehicle and close all doors before you begin. Find kia spare key or plastic piece near the bottom of the key fob. Press it until the key pops out. This key can be inserted into the driver door handle to unlock your car. To replace the battery in the key fob, take off the cover on the rear. Make use of a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and orient the new battery so that the “+” positive side faces you, and the “–” negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts. After the new battery has been installed after which you turn the key fob off and then on in the ignition for a few times until the door locks. Then you can test your Kia key fob to determine whether it's functioning properly again. How do I replace a smart key Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key has an embedded mechanical key blade, while the standard keyfob does not. Both kinds of key fobs come with a battery inside them that will eventually need to be replaced. Luckily, this is quite simple and only takes about two minutes. Before you begin before you begin, make sure that you are on a flat surface with adequate lighting and that your Kia is off. Also, keep in mind that there are tiny pieces inside the fob that could be snagged if not cautious. The small release button is located on the lower backside. This will be either a circular button or a rectangular slot. You can open the key fob by pressing the button. After the key fob has been opened, take out the battery. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you're done, your key fob should be able to lock and unlock your vehicle even if it's not running. How do I replace the mechanical key The Kia keyfob is a great convenience that allows us to lock or unlock our car by simply pressing one button. But, as with all devices it will encounter issues at times. There are solutions to solve these issues and keep your key fobs running for a long time. A dead or low-quality battery is one of the most common issues. The battery could cause the device to stop working or operate intermittently. If this is what you are experiencing it is time to replace the battery a new one. If this doesn't resolve the issue, try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new one. Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to confirm it's functioning properly. If the key fob isn't functioning, contact an authorized locksmith or dealer to help resolve the problem. To avoid locking outs in the future, ensure you have an emergency key that can work on all trunk and door cylinders.